Direct Operating Summary: The Jietai JPS-008A 0.8 L ultrasonic cleaner operates at 35 W ultrasonic output inside a seamless stamped 150 × 85 × 65 mm stainless steel inner basin (overall footprint 180 × 110 × 130 mm, gross weight 1.4 kg) without an internal heater. Always fill the basin to at least two-thirds of tank height before energizing the transducer, suspend parts in a mesh basket off the tank floor, degas fresh water-based detergent for 3 to 5 minutes, and run 3 to 15 minute digital timer cycles.
Official Factory PDF Manual: Download the original bilingual booklet Operating Instructions for 0.8L Ultrasonic Cleaner (PDF) or browse all equipment manuals in our Document Center.
1. JPS-008A 0.8 L Hardware Architecture and Step-Up Benchtop Comparison
Unlike larger industrial baths that combine resistive heating pads, drain valves, and forced-air chassis fans, the 0.8 L JPS-008A is engineered specifically as an ultra-compact laboratory, optical, electronic nozzle, and precision maintenance unit. Both the inner basin and outer housing are fabricated from corrosion-resistant stainless steel, with the 150 × 85 × 65 mm bath formed by one-piece stamping so there are zero bottom weld seams to trap polishing residue or develop pinhole leaks under acoustic fatigue. Certified under CE, EMC, RoHS, and FCC standards, the unit uses a digital countdown timer (0–30 minutes) and ambient-temperature cavitation.
Before commissioning the cleaner for small batch production or QC lab inspection, verify that your part envelope plus basket clearance fits comfortably inside the 65 mm total tank depth. When parts carry heavy machining grease requiring 50–65 °C thermal saponification or taller vertical immersion, compare the JPS-008A against Jietai’s heated small-capacity benchtop models below:
| Model Reference | Nominal Volume | Ultrasonic Power | Heating System | Inner Tank (L × W × H) | Overall Size (L × W × H) | Gross Weight |
|---|---|---|---|---|---|---|
| JPS-008A (Compact Digital) | 0.8 L | 35 W | Unheated (Ambient) | 150 × 85 × 65 mm | 180 × 110 × 130 mm | 1.4 kg |
| JPS-08A / JPS-08 (Step-Up Heated) | 1.3 L | 60 W | 100 W (20–80 °C) | 150 × 140 × 65 mm | 180 × 170 × 140 mm | 2.5 kg |
| JPS-10A / JPS-10AH (Deep Small Basin) | 2.0 L | 60–80 W | 100 W (20–80 °C) | 150 × 140 × 100 mm | 180 × 170 × 180 mm | 3.0 kg |
| JPS-20AL / JPS-23A (Power-Adjustable) | 3.0 L | 50–120 W | 100 W (20–80 °C) | 240 × 135 × 100 mm | 270 × 170 × 210 mm | 4.0–4.1 kg |
2. Pre-Start Inspection, Grounding, and Minimum Fill-Line Physics
Place the JPS-008A on a level, dry, non-conductive workbench away from steam vents, acid fumes, or conductive metal dust. Leave at least 50 mm of unobstructed air space around the stainless steel housing so heat generated by the internal driver board dissipates naturally. Confirm that the AC wall receptacle matches the rated voltage printed on the rear serial plate and provides a reliable protective earth connection.
Never energize ultrasonic cavitation with an empty tank or low liquid level. Piezoelectric ceramic transducers bonded beneath the 150 × 85 mm radiating floor rely on the acoustic load of the water column to absorb mechanical energy. Dry firing—even for 10 to 20 seconds—causes rapid thermal runaway in the epoxy bonding layer, permanently detuning or cracking the transducer element. Pour tap water, deionized water, or diluted aqueous cleaning solution into the basin until the liquid surface sits at roughly two-thirds to three-quarters of the 65 mm wall height (approximately 42–50 mm liquid depth after basket displacement), leaving enough freeboard to prevent spillover when parts are submerged.
3. Aqueous Solution Selection, Degassing, and Basket Loading Rules
Because the 0.8 L unit has no internal heater, select an aqueous surfactant or neutral/mildly alkaline concentrate formulated to emulsify light oils, fingerprints, flux residue, or lapping dust between 20 °C and 40 °C. If warm water is helpful, you may pre-mix solution using warm water up to 45 °C, provided the liquid never exceeds 60 °C and contains zero volatile solvents.
- Mandatory Degassing Run: Freshly poured water contains dissolved air that cushions imploding bubbles and absorbs acoustic energy. Before lowering workpieces into a fresh bath, run the JPS-008A empty (liquid only) for 3 to 5 minutes until visible rising gas strings subside and the acoustic hiss stabilizes into a crisp, uniform pitch.
- Zero Direct Floor Contact: Always suspend small screws, watch movements, carburettor jets, dental burs, optical mounts, or sensor housings inside a stainless steel mesh basket or hang them from a support rod. Resting metal components directly on the 150 × 85 mm bottom plate damps local diaphragm vibration, scores the stamped stainless surface, and creates localized hot spots above the transducer crystal.
- Part Orientation for Blind Holes: Tilt threaded blind bores, capillary tubes, and recessed cavities slightly upward when submerging them so trapped air pockets vent immediately rather than blocking liquid contact inside the bore.
- Prohibited Media: Never pour flammable low-flashpoint solvents (gasoline, acetone, isopropyl alcohol, toluene, ethyl ether) directly into an open non-explosion-proof benchtop bath. Ultrasonic atomization generates ignitable vapor mist near standard electrical switches. Likewise, avoid uninhibited hydrochloric, hydrofluoric, or strong sulfuric acids and chloride bleaches that pit stainless steel.
4. Timer Cycle Execution, Duty Rest Intervals, and Post-Clean Rinsing
Connect the detachable power lead, verify the liquid level covers the submerged workpieces completely, and set the digital display timer according to soil tenacity: 2 to 4 minutes for dust on optical mounts or laboratory glassware, 5 to 10 minutes for light cutting fluid on brass nozzles or PCB Flux subassemblies, and 10 to 15 minutes for oxidized instrument joints. Place the stainless steel lid over the basin during cavitation to reduce airborne aerosol mist and acoustic noise.
Because compact 0.8 L and 1.3 L housings cool passively without the forced-air chassis fan installed on Jietai models of 10 L and above, allow a 10-minute rest pause after 25 to 30 minutes of continuous ultrasonic operation. Remember that continuous cavitation naturally warms a small 0.8 L water volume over repeated cycles. Once the digital timer reaches zero, lift the basket, allow drag-out liquid to drain for 10 seconds, rinse parts immediately in clean deionized water to prevent detergent spotting, and dry with filtered compressed air.
5. Draining, Basin Care, and Fault Diagnosis Matrix
Drainage ball valves are fitted on Jietai benchtop cleaners of 6 L capacity and above; therefore, the 0.8 L JPS-008A is emptied manually. Always unplug the power cord before lifting the 1.4 kg chassis. Pour spent solution out over a corner lip away from the front digital display panel and rear power socket, wipe settled sludge from the seamless basin with a soft lint-free cloth, rinse with clean water, and wipe dry. Never scrape the bottom radiating surface with wire brushes or abrasive pads.
| Observed Symptom | Primary Engineering Cause | Corrective Action |
|---|---|---|
| Display stays dark when plugged in | Loose IEC power cord, unpowered outlet, or blown internal fuse from voltage surge | Reseat power cord firmly, verify wall voltage, inspect rear fuse holder after unplugging |
| Audible buzz present, weak cleaning action | Fresh aerated water not degassed, overloaded part mass, or parts resting on tank floor | Degas bath 5 minutes, reduce batch weight below 0.3 kg, elevate parts in mesh basket |
| Cloudy film or white spots after drying | Saturated bath oil load or hard-water mineral residue without post-rinse | Replace spent cleaning bath and add a clean DI water dip rinse immediately after cleaning |
| Chassis feels warm during extended batches | Continuous duty cycles exceeding 30 minutes without passive heat dissipation pause | Pause unit 10–15 minutes; if hourly throughput is continuous, step up to fan-cooled 10 L+ JPS series |
If your components require heated degreasing, sweep-frequency degassing, or multi-stage production throughput beyond a single 0.8 L laboratory bath, submit sample parts for a complimentary 7 to 10 working day process evaluation through our Free Sample Cleaning Trial page or contact Jietai engineering.
Frequently Asked Questions: 0.8 L Benchtop Ultrasonic Operation
Can I run isopropyl alcohol (IPA) directly inside the 0.8 L JPS-008A tank?
No. Open benchtop ultrasonic cleaners are not explosion-proof; ultrasonic cavitation atomizes volatile solvents like IPA or acetone into flammable vapor mist. For flammable solvent dehydration, use sealed indirect Glass-Beaker water-bath methods in a ventilated fume hood for tiny lab samples, or specify Jietai’s JTW-4096AD explosion-proof ultrasonic system for industrial production.
Why does the JPS-008A omit a built-in heater and drain ball valve?
At 0.8 L (150 × 85 × 65 mm, 1.4 kg total weight), bottom surface area is dedicated entirely to the 35 W piezoelectric transducer, and pouring out 500–600 mL by hand takes seconds. Jietai installs thermostatic heaters (20–80 °C) starting from 1.3 L (JPS-08A), drain ball valves starting at 6 L, and chassis cooling fans starting at 10 L.
How often should the cleaning liquid in a 0.8 L ultrasonic bath be changed?
Replace the bath whenever the solution turns visibly turbid, emulsified oil floats to the surface on shutdown, or cavitation sound dulls noticeably—typically every 3 to 6 small maintenance batches because a 0.8 L liquid volume saturates quickly with suspended soils.
Matched Jietai Ultrasonic Equipment, Categories & Engineering Guides
Matched Industrial & Benchtop Models: Digital Power Adjustment Series · Digital Series · Dual-frequency machine · Digital Multi-Functional Series · Mechanical Series · Smart Digital Three-Frequency Series · Digital Black Titanium Series
Product Series & Technical Archives: Bench Standard Machine · Digital Series · Digital Black Titanium Series · Digital Power Adjustment Series · Dual-Frequency Machine · Mechanical Series · Smart Digital Three-Frequency Series
Related Process Engineering Guides: Operating Instructions for Multifunctional, Mechanical and Digital Series · Benchtop Ultrasonic Cleaner Sizes from 1.3 L to 30 L: Tank Dimensions, Power and Which Series · How to Use and Maintain a Benchtop Ultrasonic Cleaner: Setup, Degas, Heating, Cleaning the Tank and Troubleshooting · Ultrasonic Cleaning Basket: How It Changes Cleaning Results · Specialized Ultrasonic Lines: Explosion-Proof IPA Dehydration, 30-Tank Valve EP/Passivation & Centrifugal Drying

