Direct Control & Commissioning Summary: Jietai’s JPS Mechanical (JPS-08 to JPS-100), Digital (JPS-008A to JPS-100A), and Digital Multi-Functional (JPS-23A to JPS-1030A) benchtop ultrasonic cleaners span 1.3 L to 30 L (60 W to 600 W ultrasonic power, 100 W to 600 W heating, 20–80 °C thermostat). Models of 6 L and above include side drainage ball valves, models of 10 L and above integrate high-efficiency cooling fans, and 22 L / 30 L units feature heavy-duty 1.5 mm stainless steel basins.
Official Factory Manual PDF: Download the complete bilingual booklet Operating Instructions for Multifunctional, Mechanical and Digital Series (PDF) or visit our Document Center.
1. Differences Between Mechanical, Standard Digital, and Digital Multi-Functional Controls
All three JPS benchtop families share CE, EMC, RoHS, and FCC compliance, stainless steel inner tanks and outer housings, and imported industrial-grade piezoelectric transducer assemblies. Selecting and operating the right panel depends on how tightly your workshop SOP controls cycle repeatability, ultrasonic amplitude, and dissolved gas removal:
- Mechanical Series (JPS-08 to JPS-100): Uses two industrial rotary dials—one 0–30 minute mechanical timer (with continuous hold position where marked) and one 20–80 °C capillary thermostat knob. Operators wearing wet nitrile gloves in machine shops favor rotary dials for instant tactile operation.
- Standard Digital Series (JPS-008A to JPS-100A): Replaces rotary knobs with dual LED readouts showing actual vs. set bath temperature (20–80 °C, except the unheated 0.8 L JPS-008A) and digital countdown minutes (0–30 minutes) for auditable QC cycle logging.
- Digital Multi-Functional Series (JPS-23A to JPS-1030A, plus JPS-AL / JPS-AH / JPS-SP variants): Extends digital timing to 1–99 minutes, adds adjustable ultrasonic power modulation (40–100% output range, e.g., 50–120 W on 3 L up to 240–600 W on 30 L), and provides dedicated Degassing / Sweep Frequency modes to eliminate standing-wave dead zones on delicate PCBs, optical glass, and thin-wall aluminum parts.
2. Complete 1.3 L to 30 L JPS Tank Size, Ultrasonic Power, and Heater Matrix
Before filling or wiring high-capacity 22 L and 30 L units (which draw combined 600 W ultrasonic + 600 W heating loads), verify model capacity, inner basin dimensions, and hardware thresholds across the ten heated JPS frame sizes:
| Capacity | Mechanical Model | Digital Model | Multi-Functional Model | Max Ultrasonic Power | Heating Power | Inner Tank (L × W × H) |
|---|---|---|---|---|---|---|
| 1.3 L | JPS-08 | JPS-08A | — | 60 W | 100 W | 150 × 140 × 65 mm |
| 2.0 L | JPS-10 | JPS-10A | — | 80 W | 100 W | 150 × 140 × 100 mm |
| 3.0 L | JPS-20 | JPS-20A | JPS-23A (50–120 W) | 120 W | 100 W | 240 × 135 × 100 mm |
| 6.0 L | JPS-30 | JPS-30A | JPS-36A (70–180 W) | 180 W | 300 W | 300 × 150 × 150 mm |
| 10.0 L | JPS-40 | JPS-40A | JPS-410A (100–240 W) | 240 W | 300 W | 300 × 240 × 150 mm |
| 14.0 L | JPS-50 | JPS-50A | JPS-514A (120–300 W) | 300 W | 300 W | 300 × 240 × 200 mm |
| 15.0 L | JPS-60 | JPS-60A | JPS-615A (150–360 W) | 360 W | 300 W | 330 × 300 × 150 mm |
| 19.0 L | JPS-70 | JPS-70A | JPS-719A (170–420 W) | 420 W | 300 W | 330 × 300 × 200 mm |
| 22.0 L | JPS-80 | JPS-80A | JPS-822A (200–480 W) | 480 W | 600 W | 500 × 300 × 150 mm |
| 30.0 L | JPS-100 | JPS-100A | JPS-1030A (240–600 W) | 600 W | 600 W | 500 × 300 × 200 mm |
3. Step-by-Step Commissioning: Valve Closure, Fill Height, Pre-Heating, and Degassing
Follow this five-step startup sequence on every shift to protect heaters and piezoelectric transducers from thermal shock:
- Close the Drain Ball Valve (6 L to 30 L Models): On JPS-30 / 30A / 36A (6 L) through JPS-100 / 100A / 1030A (30 L), confirm the side stainless ball valve handle sits perpendicular (closed) before adding water, and connect a heat-resistant drain hose to a floor gully or collection carboy.
- Fill to the Two-Thirds Operating Mark: Add water and measured aqueous detergent concentrate until the bath reaches two-thirds to three-quarters of inner tank height (minimum 100 mm liquid depth on 150 mm deep tanks; minimum 135 mm on 200 mm deep tanks). Never turn on either the heater or ultrasonic switch below this level—side/bottom heater pads exposed above the water line burn out rapidly.
- Pre-Heat to Target Process Temperature (20–80 °C): Set the thermostat between 45 °C and 60 °C for alkaline metal degreasing, or 35 °C to 45 °C for electronics, medical instruments (blood/protein removal below 45 °C prevents coagulation), and coated optics. Running ultrasonic agitation briefly circulates water past the sensor so bath temperature equalizes faster. Avoid running above 75 °C unless required, as water vapor pressure above 80 °C cushions cavitation bubble collapse.
- Run Degas & Sweep Conditioning: On Digital Multi-Functional models (JPS-23A to JPS-1030A), press the Degas function for 5 minutes whenever fresh solution is prepared; pulsed cavitation coalesces dissolved oxygen and nitrogen micro-bubbles so full acoustic shockwaves reach workpiece surfaces.
- Dial Power Percentage & Suspend Basket: Lower workpieces inside a stainless mesh basket—never directly onto the 1.5 mm stamped/welded radiating floor—and adjust power between 40% and 70% for fragile wire-bonded boards or thin coatings, or 80% to 100% for machined steel, cast iron, and sintered filters.
4. Cooling Fan Clearance (10 L+), Solvent Prohibition, and Daily Maintenance
Models of 10 L and above (JPS-40 / 40A / 410A upward) house active cooling fans beneath the chassis. Keep the workbench surface clear of rags, plastic wrap, or standing water puddles that could block bottom intake louvers, and maintain 100 mm rear/side clearance around 22 L and 30 L units. Never pour flammable organic solvents (acetone, IPA, gasoline, hydrocarbon spirits) or strong chloride/mineral acids directly into any open JPS benchtop basin.
At shift end, turn off heating and ultrasonic switches, allow hot baths above 55 °C to cool before draining through the ball valve, flush settled machining swarf from the basin corners with clean water, and wipe the stainless interior dry so chloride ions in tap water cannot pit the radiating diaphragm overnight. When batch weight, oil drag-in, or multi-rinse cleanliness specifications outgrow a single 30 L benchtop bath, test your parts free of charge (7–10 working days) via our Sample Cleaning Trial program or request a multi-tank configuration from Jietai Customization Engineering.
Frequently Asked Questions: JPS Mechanical, Digital & Multi-Functional Cleaners
Why does cavitation seem weaker when I set the thermostat to 80 °C?
In aqueous ultrasonic baths, cavitation intensity peaks between roughly 45 °C and 65 °C. Approaching 80 °C increases water vapor pressure inside each cavitation bubble, cushioning implosion shockwaves. Keep general degreasing between 50 °C and 60 °C unless thermal wax melting specifically requires higher heat.
When should I step down ultrasonic power to 40–60% on Digital Multi-Functional models?
Use reduced power (40–60%) together with Sweep mode when cleaning thin anodized aluminum, optical AR coatings, fine pitched PCBs, or precision brass metering orifices where 100% full-wave cavitation at fixed frequency could cause micro-erosion.
What distinguishes the 22 L and 30 L JPS basins from smaller 3 L–19 L units?
JPS-80 / 80A / 822A (22 L) and JPS-100 / 100A / 1030A (30 L) share a larger 500 × 300 mm footprint (150 mm vs. 200 mm depth), upgrade heating power to 600 W, and utilize reinforced 1.5 mm thick stainless basins to handle heavier industrial baskets without floor deflection.
Matched Jietai Ultrasonic Equipment, Categories & Engineering Guides
Matched Industrial & Benchtop Models: Digital Power Adjustment Series · Digital Series · Dual-frequency machine · Digital Multi-Functional Series · Mechanical Series · Smart Digital Three-Frequency Series · Digital Black Titanium Series
Product Series & Technical Archives: Bench Standard Machine · Digital Series · Digital Black Titanium Series · Digital Power Adjustment Series · Dual-Frequency Machine · Mechanical Series · Smart Digital Three-Frequency Series
Related Process Engineering Guides: Operating Instructions for 0.8L Ultrasonic Cleaner · Benchtop Ultrasonic Cleaner Sizes from 1.3 L to 30 L: Tank Dimensions, Power and Which Series · How to Use and Maintain a Benchtop Ultrasonic Cleaner: Setup, Degas, Heating, Cleaning the Tank and Troubleshooting · Ultrasonic Cleaning Basket: How It Changes Cleaning Results · Specialized Ultrasonic Lines: Explosion-Proof IPA Dehydration, 30-Tank Valve EP/Passivation & Centrifugal Drying

